Friday, 1 December 2017

Getting Ready For Snow

Getting Ready For Snow


If you have fuel left over from summer equipment then it is best to use it up in your vehicle. Fuel is blended for the average atmospheric conditions at the time of sale, so winter fuel is different than summer fuel. The formula used for blending fuel changes many times during the year. Unstabilized fuel loses 2-3 octane points per month. This is just one of the problems with old fuel. We have detailed fuel memos available for free if anyone would like a copy.


Before it snows pick up anything laying around in the areas where a snow blower will be operated. Solid objects like pieces of wood will break shear pins if picked up but will sometimes pass through the augers and get caught up in the impeller fan. This can cause major damage. Extension cords or rope are flexible so will cause a shear pin to break. They will be wound up into the augers until bound so tightly something breaks. When removing something from the augers always have the engine shut off. Also be aware that even with the engine shut off the augers can move. Whatever is caught has been jammed by a strong force. When the object is removed the auger can rotate a small amount so be careful with where your fingers are.


Tips for removing stuck items and replacing shear pins are as follows. Shut the engine off. Some items can simply be pulled out if the blower was stopped quickly. If an object is stuck, remove the shear bolt. This will allow the auger to move freely so the object can be removed. If the shear bolt was bent then replace it. Shear bolts are cheap. Augers & gearboxes are expensive. Always use a proper shear bolt. They are designed to shear and protect the system. Some people use a grade 2 bolt but these are stronger and will stretch before breaking. Damage results. We have seen augers that rip into 2 pieces because someone has installed an even harder grade 5 bolt. Expensive. Newspapers are common items to pick up with a snow blower. Normally they can just be pulled out. If they are really stuck the best way to remove it is to bring the blower into a heated garage. When the paper is warm it is soft and can be removed easily. A heat gun or hair dryer can be used if a heated garage is not available.


Shear pin replacement: Sometimes when they break there will be a broken piece stuck in the auger shaft. The hole location is not always in a convenient location. With the engine shut off, hold the auger handle down and slowly pull the rewind. This will cause the auger system to rotate. It takes quite a few pulls to fully rotate the auger system once so you may have to pull 3 or 4 times. Once you can see the hole in the auger shaft you can knock out the remains of the old bolt with a hammer & punch then install the new bolt. Always keep some spare shear bolts.


Maintenance pays off. Pre season maintenance is the way to go. Your snow blower is unlikely to give you any problems during the summer. During a major snowfall when a snow blower is really working is the same time that any problems are going to show up. Unfortunately the majority of people run them until they break. It is the same as doing all your automotive maintenance while hooked up to a tow truck after breaking down on the side of the highway. It is always more expensive and never convenient. In our industry we get a flood of broken snow blowers after every major snowfall. Every person wants theirs fixed first because their driveway is full of snow! We recommend having pre season maintenance performed in the spring. That way it is properly stored for the off season and is ready to go when the snow returns.

We could add much more to this post so we will revisit this topic again in the future.  

Thursday, 9 August 2012

The Name Game

One of the most confusing and frustrating aspects of the outdoor power equipment field for consumers is the overwhelming amount of brand names in the marketplace. There is no end to the volume of sales propaganda from the mass merchants and manufacturers but how does the average person make a wise choice?

Obviously I have a biased opinion and think you should avoid the mass merchants altogether. That opinion is also based on the experience of seeing so many people go so far wrong with their purchasing decisions at the mass merchants. There are many reasons why but today I will concentrate on the name game.

Manufacturers love big volumes. It keeps their factories humming and the shareholders happy. The problem begins with how far a manufacturer is prepared to go in order to achieve those numbers. Unfortunately many have taken the route of using a well respected brand, cheapening up the product and putting it in the box stores. The big retail chains will squeeze every cent out of a manufacturer. The manufacturer still has to make a profit to stay in business. Only one route to take if you want to stay in the big box store. Cut every corner when you manufacture the product. You can't blame the box stores. They work on volume and it does them no good to have your product last for 20 years. They would like you to kindly replace it every year or two. Don't get me wrong. I love the box stores for a different reason. They pump out large volumes of equipment that rapidly need repair. This keeps our parts & service departments very busy.

It works wonders for awhile. The brand name has previously earned respect so people buy with confidence, only later are they disappointed with the results. It takes many years to finally drag down a brand name. By that time the CEO of the manufacturer has usually moved on with his bags of cash for all the wonderful sales numbers he has achieved over the previous few years. Long term though the brand is in a downward spiral as word gets out and people refuse to be duped again. Until finally they just put a whole new name on the same bad old product and the process begins anew.

Some big companies have bought up brand names of companies that were well respected but have gone out of business. The respected brand name is revived and applied to new, substandard products that floods the stores. This is very common.

The larger manufacturers also like to put out the same product in different colors & brand names. This lets the retailer claim an exclusive with the brand. An uninformed consumer may pay hundreds of dollars more for a product that is exactly the same as a less expensive brand at another retailer.

How is a person to know what they are buying? You have to talk with someone who is in the industry. In outdoor power equipment you need to talk to local dealers. You don't have to talk to just one. Find one you are comfortable with or get a variety of opinions from a number of different dealers. The dealer will be up to speed on the current antics of the manufacturers and stores. Now you will have solid facts to help you with a purchasing decision. If you are considering purchasing equipment then this is absolutely the critical first step. Do not trust internet based opinions as many of those have no depth of experience.

Personally I do not trust buying guides put out by different consumer groups. I have seen some real lemons promoted as best buys. Among outdoor power equipment dealers we all have a great laugh at some of the recommendations since we have seen first hand how poorly that product performs. I have also seen identical products manufactured under different names receive wildly different reviews. It is the exact same product! Maybe the reviewer liked the blue color better than the green color or it just simply clashed with his wardrobe.

The situation in the outdoor power equipment field is very much like the same game played in the home appliance industry and many others. Take some time, visit a few dealers. You will meet some nice people and gain valuable knowledge.

Saturday, 24 March 2012

One...Two...Three..Go!

Well....here we go. For quite some time we have been saying "we need to start a blog". This is the start.

There is so much information on outdoor power equipment that many people just get confused. Much of this information is incorrect. It may be an honest mistake, corporate spin, marketing or relying on people who seem to know what they are talking about but are misinformed. Trusting friends or neighbors can be hit and miss depending on their level of knowledge. Online sources vary wildly in the quality of information. Major retailers do not employ product specialists who are experts in their field. Even consumer reports can be misleading. Why is the blue piece of equipment rated a best buy but the exact same piece of equipment in green is rated poorly? It makes life difficult for the average person to make an informed decision when it comes to equipment.

My goal with this blog is to take the common questions that I hear all the time and provide the best advice. I have over 30 years of industry experience, am a licensed Marine and Small Powered Technician, certified Briggs & Stratton Master Technician and have operated Saulco Enterprises for the last 15 years. Myself and our technicians spend many days every year in service schools operated by the various manufacturers we represent. This keeps us current with the rapidly changing field of outdoor power equipment. Additionally I am also on the OPE Council for the North American Equipment Dealers Association (NAEDA). This provides me with a wide perspective of the outdoor power equipment field.

The opinions I have here are my own. I hope to provide honest, practical advice that will help you select, use and properly care for your equipment.

Regards
Mark